key features: ? 1w output power ? miniature sip case ? 3,000 vdc isolation ? single & dual outputs ? complies to rfi standards ? >1.12 mhour mtbf ? 36 standard models ? industry standard pin-out d100i high isolation miniature, 1w sip dc/dc con vert ers series input parameter conditions min. typ. max. units input voltage range 5 vdc input 4.5 5.0 5.5 vdc 12 vdc input 10.8 12.0 13.2 24 vdc input 21.6 24.0 26.4 48 vdc input 43.2 48.0 52.8 input filter internal capacitor re? ected ripple current 12 h source inductance 20 ma p - p output parameter conditions min. typ. max. units output voltage accuracy 3.0 % output voltage balance dual output , balanced loads 1.0 % line regulation for vin change of 1% 1.2 % load regulation (note 1) see model selection guide ripple & noise (20 mhz) (note 2) 75 mv p - p output power protection 110 % temperature coef? cient 0.02 %/oc output short circuit momentary (0.5 sec.) general parameter conditions min. typ. max. units isolation voltage 60 seconds 3,000 vdc isolation resistance 500 vdc 1,000 m isolation capacitance 100 khz, 1v 60 pf switching frequency 80 khz emi/rfi en55022 b, en55024 b, iec 61000-4-2, iec 61000-4-3, fcc 47 cfr part 15 b environmental parameter conditions min. typ. max. units operating temperature range ambient -40 +25 +85 oc operating temperature range case +100 oc storage temperature range -40 +125 oc cooling free air convection humidity rh, non-condensing 95 % physical case size (5v 12v & 24v input models) 0.76 x 0.24 x 0.39 inches (19.5 x 6.0 x 10.0 mm) case size (48v input models) 0.76 x 0.28 x 0.39 inches (19.5 x 7.2 x 10.0 mm) case material non-conductive black plastic (ul94-v0) weight 0.08 oz (2.3g) reliability speci? cations parameter conditions min. typ. max. units mtbf mil hdbk 217f, 25oc, gnd benign 1.12 mhours absolute maximum ratings parameter conditions min. typ. max. units input voltage surge (1 sec) 5 vdc input -0.7 7.0 vdc 12 vdc input -0.7 15.0 24 vdc input -0.7 28.0 48 vdc input -0.7 54.0 lead temperature 1.5 mm from case for 10 sec 260 oc internal power dissipation all models 450 mw caution: exceeding absolute maximum ratings may damage the module. these are not continuous operating ratings. micropower direct 292 page street suite d stoughton, ma 02072 usa t: (781) 344-8226 f: (781) 344-8481 e: sales@micropowerdirect.com w: www.micropowerdirect.com rohs compliant electrical speci? cations speci? cations typical @ +25c, nominal input voltage & rated output current, unless otherwise noted. speci? cations subject to change without notice.
notes: ? all dimensions are typical in inches (mm) ? tolerance x.xx = 0.01 ( 0.25) ? pin 1 is marked by a dot or indentation on the side of the unit model number input output load regulation (%, max) ef? ciency (%, typ) fuse rating slow-blow (ma) voltage (vdc) current (ma) voltage (vdc) current (ma, max) current (ma, min) nominal range full-load no-load d101i 5 4.5 - 5.5 267 30 3.3 303.0 6.0 10 75 500 d102i 5 4.5 - 5.5 256 30 5.0 200.0 4.0 10 78 500 d103i 5 4.5 - 5.5 267 30 9.0 111.0 2.2 10 75 500 d104i 5 4.5 - 5.5 263 30 12.0 83.3 1.6 10 76 500 d105i 5 4.5 - 5.5 263 30 15.0 66.6 1.3 10 76 500 d106i 5 4.5 - 5.5 270 30 5.0 100.0 2.0 10 74 500 d107i 5 4.5 - 5.5 256 30 9.0 55.5 1.1 10 78 500 D108I 5 4.5 - 5.5 256 30 12.0 41.6 0.8 10 78 500 d109i 5 4.5 - 5.5 250 30 15.0 33.3 0.6 10 80 500 d111i 12 10.8 - 13.2 113 20 3.3 303.0 6.0 10 74 200 d112i 12 10.8 - 13.2 113 20 5.0 200.0 4.0 10 74 200 d113i 12 10.8 - 13.2 111 20 9.0 111.0 2.2 10 75 200 d114i 12 10.8 - 13.2 108 20 12.0 83.3 1.6 10 77 200 d115i 12 10.8 - 13.2 106 20 15.0 66.6 1.3 10 78 200 d116i 12 10.8 - 13.2 111 20 5.0 100.0 2.0 10 75 200 d117i 12 10.8 - 13.2 109 20 9.0 55.5 1.1 10 76 200 d118i 12 10.8 - 13.2 106 20 12.0 41.6 0.8 10 78 200 d119i 12 10.8 - 13.2 104 20 15.0 33.3 0.6 10 80 200 d121i 24 21.6 - 26.4 56 10 3.3 303.0 6.0 10 75 100 d122i 24 21.6 - 26.4 54 10 5.0 200.0 4.0 10 77 100 d123i 24 21.6 - 26.4 56 10 9.0 111.0 2.2 10 75 100 d124i 24 21.6 - 26.4 53 10 12.0 83.3 1.6 10 78 100 d125i 24 21.6 - 26.4 53 10 15.0 66.6 1.3 10 78 100 d126i 24 21.6 - 26.4 56 10 5.0 100.0 2.0 10 74 100 d127i 24 21.6 - 26.4 54 10 9.0 55.5 1.1 10 76 100 d128i 24 21.6 - 26.4 53 10 12.0 41.6 0.8 10 78 100 d129i 24 21.6 - 26.4 53 10 15.0 33.3 0.6 10 78 100 d131i 48 43.2 - 52.8 29 6 3.3 303.0 6.0 10 72 100 d132i 48 43.2 - 52.8 29 6 5.0 200.0 4.0 10 72 100 d133i 48 43.2 - 52.8 28 6 9.0 111.0 2.2 10 74 100 d134i 48 43.2 - 52.8 28 6 12.0 83.3 1.6 10 74 100 d135i 48 43.2 - 52.8 28 6 15.0 66.6 1.3 10 75 100 d136i 48 43.2 - 52.8 30 6 5.0 100.0 2.0 10 70 100 d137i 48 43.2 - 52.8 29 6 9.0 55.5 1.1 10 72 100 d138i 48 43.2 - 52.8 28 6 12.0 41.6 0.8 10 74 100 d139i 48 43.2 - 52.8 28 6 15.0 33.3 0.6 10 74 100 pin single dual pin single dual 1 +vin +vin 6 no pin common 2 -vin -vin 7 +vout +vout 5 -vout -vout notes: 1. output load regulation is speci? ed for a load change of 20% to 100%. 2. these units do not require external components to operate, but the use of an input capacitor (10 f) may enhance performance in some applications. it is recommended that an input capacitor of 4.7 uf to 47 uf (dependent upon the application) be used on 48v input model. an output capacitor (4.7 f to 100 f or 4.7 f to 68 f) may be used to reduce ripple. to improve emi performance, a simple ? lter network consisting of a 10 uf to 100 uf capacitor and 12 u h inductor should be effective. 3. these units will operate at no load without damage, but may not meet all speci? cations. 4. dual output units may be connected to provide a 10v, 18v, 24v or 30 vdc output. to do this, connect the load across the positive (+vout) and negative (-vout) outputs and ? oat the output common. 5. it is recommended that a fuse be used on the input of a power supply for protection. see the table above for the correct rating. derating curve notes: ? a ll d im e n s ? t olerance x ? p in 1 is ma r the si de of micropower direct www.micropowerdirect.com 292 page street, ste d, stoughton, ma 02072 ? tel: (781) 344-8226 ? fax: (781) 344-8481 ? e-mail: sales@micropowerdirect.com model selection guide mechanical dimensions pin connections single output (f max) 220 dual output (f max) 100 capacitive load other input/output combinations are available (i.e. 24.0 vdc). contact the factory for details at: sales@micropowerdirect.com
|
